011
CNC machining shop
69 CNC machining centers — 38× 3-axis, 13× 4-axis, 18× 5-axis
HAFO MOULD
Our Factory & Equipment
HAFO Mould operates from a 5,000 m² factory in Chang'an, Dongguan — the same company, Haifu Mould Industry Limited, at work since 2007. Eighty people work here, 35 of them engineers, across four connected workshops:
the CNC machining shop, the mold toolroom, the injection molding shop and the inspection room. This page lists the equipment in those rooms plainly, because equipment lists are where factory websites are most often inflated.
Equipment at a Glance
Ours is verifiable: the photographs on this page were taken in this factory, of the machines described below — and buyers are welcome to verify it all on a video call or a visit. Maximum CNC travel across the machining shop is 800 mm (31.5 in).
022
Toolroom
13 high-speed CNC machines · 8 EDM machines · 6 wire-cut machines (incl. Sodick) · DAHLIH gantry machining center
033
Injection molding shop
Haitian injection molding machines, 90T–470T clamping force — including 2× 360T two-shot machines
044
Inspection room
3 fully automatic CMMs
055
Facility
5,000 m² · 80 staff, 35 engineers · Dongguan, Guangdong · operating since 2007
WORKSHOP
The CNC Machining Shop
Why it matters to your order: every service on this site — CNC machining, mold making, injection molding — is produced in these rooms, by this company. Nothing is brokered onward. When you ask who made your part, the answer is on this page. The sections below walk through each workshop.
Sixty-nine machining centers
Sixty-nine machining centers form the core of the factory: 38 three-axis, 13 four-axis and 18 five-axis machines, arranged for both prototype and production work. Three-axis centers handle plates, brackets and housings efficiently;
Five-axis fleet
the five-axis fleet machines complex, multi-face parts in a single setup; turning and mill-turn capacity in the same shop completes rotational parts without a second supplier.
Parts sold on this site
The CNC shop produces the parts sold on this site — aluminum, stainless, steel, brass, copper, titanium, magnesium and engineering-plastic components — and it also roughs and finishes mold components for the toolroom next door,
Same discipline
which is why our machining tolerances and our mold tolerances are the same discipline.
WORKSHOP
The Toolroom
Molds are built here, not bought in. The toolroom runs 13 high-speed CNC machines for cavity and core detail, 8 EDM machines for sharp internal corners and hardened-steel features, and 6 wire-cut machines — including Sodick equipment — for precise through-profiles in mold plates and inserts.
The DAHLIH gantry machining center handles the large mold bases and plates that smaller centers cannot take. This is the room behind our injection molds and two-shot tooling: design, machining, fitting and polishing within one department,
Inside the Toolroom
WORKSHOP
The Injection Molding Shop
Production molding runs on Haitian injection machines from 90T to 470T clamping force, covering small precision components through to larger housings. The fleet includes two 360T two-shot machines, which run our two-color and overmolding work
— a second material molded over or alongside the first in a single cycle. Because the toolroom is in the same building, molds move from trial to production, and from production back to maintenance, without leaving the factory.
WORKSHOP
The Inspection Room
Three fully automatic CMMs anchor the inspection room, verifying dimensions and geometry against customer drawings — first articles, in-process checks and final inspection before packing.
Material and surface-treatment certificates are compiled with orders here, and this is where the inspection reports offered with every order are produced.
One Roof, One Accountable Supplier
The commercial point of this equipment list is simple. A machined prototype, the mold it grows into, and the molded production that follows can all be made in this factory, by one team, under one ISO 9001:2015-certified quality system (scope: Manufacturing of Hardware Molds and Parts).
FAQ
Buyers worldwide already receive parts from these rooms, shipped on DDP, EXW or FOB terms. If your current supply chain splits those steps across three vendors and a broker, this page is what consolidation looks like.
Want to see what these machines can do with your part?
Upload your drawing for a free DFM review and a quote within 24 hours.